Optical characterization of polycarbonate: Influence of additives on optical properties

In laser transmission welding of thermoplastics the optical properties of the joining parts determine the quality of the welding result. Especially, the scattering of laser radiation in the transparent welding part has an impact on weld seam properties. This scattering is caused by additives. For polycarbonate (PC) with different additives the transmittance, the reflectance and the collimated transmittance are measured with a UV‐VIS‐NIR spectrometer. From this data, the optical properties, such as scattering coefficient, absorption coefficient, and anisotropy factor are calculated. The calculations are made with the aid of the four‐flux model of radiation transport in the diffusive approximation. The results show that the additives have a significant influence on the scattering coefficient. For most additives under consideration the scattering is forward directed, which means that most of the radiation is transmitted into the absorbing welding part. However, the power density distribution of the transmitted radiation may differ significantly from PC without additives. So, the weld seam may also differ due to different additives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 451–455, 2010     

Carbon dioxide reforming of methane on monolithic Ni/Al2O3-based catalysts

Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the surface acid-base properties of catalysts by introduction of alkali metal (Na, K) oxides inhibits the carbonization and as a result, improves the operational stability of these catalysts. An effect of promotion of nickel-alumina based composite doped by lanthanum oxide is found. This effect, caused by an additional route for the CO2 activation on Ni-La2O3/Al2O3/cordierite catalyst, is displayed in increase of methane conversion under conditions of an oxidant excess.     

Stability of model recycled mixed plastic waste compatibilised with a cooperative compatibilisation system

The effect of the degree of degradation of the components of a model municipal plastic waste (a mixture of low-density polyethylene, high-density polyethylene, polypropylene and high-impact polystyrene) on the toughness and stability of recyclates compatibilised with a cooperative compatibilisation system (a mixture of ethylene-propylene statistical and styrene-butadiene block copolymers with a secondary amine-based stabiliser) was studied. It was shown that good impact strength was achieved for recyclates having components with a low or medium degree of degradation. Mechanical properties of recyclates having the components with a high degree of degradation are deteriorated. The addition of the cooperative compatibilisation system leads to a higher thermo-oxidative stability of recyclates irrespective of the degree of degradation of their components. Photo-oxidative stability of the recyclates is low but it can be improved to a satisfactory level by the addition of carbon black or a commercial photo-stabiliser.     

Characterization of the mesostructure of HDPE under “in situ” uniaxial tensile test by incoherent polarized steady‐light transport

This study presents quantitative results related to in situ investigation of the microstructural evolutions of high‐density polyethylene with deformation. These results were obtained thanks to a novel technique (IPSLT) based on the polarized light scattering transport phenomenon. The heterogeneities produced during whitening of the polymer bulk are characterized at the mesoscale level (from hundred of nanometers to a few micrometers). The technique is described as well as the identified parameters it provides, namely: the average size of the scatterers, the anisotropy developed in the medium, and the light transport length, representative of both the volume fraction and size of the heterogeneities. Results obtained during video‐controlled tensile experiments confirm those obtained previously with X‐ray microtomography. They put forward the role of morphological transformations of the amorphous/crystalline phases (especially regarding the creation of fibrillar assemblies) rather than the cavitation phenomenon. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

孔型立轧过程的三维刚塑性有限元分析

采用三维刚塑性有限元法对２Ｓ－Ａｌ板孔型立轧稳态过程进行了分析和比较，所得轧件断面形状，轧制力及轧制力矩与文献「１」的实验结果吻合很好，计算精度有所提高。     

Relaxation mechanism of rotational type in fracture of weld joints for austenic steels

Studied is the mesoscale behavior of plastic deformation and fracture of weld joints for austenic steels. Large-scale rotational modes of deformation in heat affected zones are identified with the first stage of formation of band structures; it is related to the “traveling neck” phenomenon in the base metal. The second stage is connected with crack generation and the state of affairs in the heart-affected zone.     

固体材料的变形—断裂转变

总结评述了固体材料表现出韧或脆性,也即变形和断裂及其相互转变的力学条件。收列大量事例以说明变形—断裂转变的各种表现形式及各种条件参数的影响。提出一种能概括各种变形和断裂行为的变形—断裂转变示图。总结表明,材料的断裂行为主要受尺寸参数D和性能参数(K_c/σs)~2控制,在不同的状态条件下,可表现为弹性变形、弹性断裂、弹塑性变形、弹塑性断裂、塑性流动或倒塌、全塑性断裂等多种力学行为。